1. Swing over lathe diameter 500mm
2. Max. turning length 250mm
3. Maximum rotation diameter of tool table Ø160
4. Maximum bar material diameter 50mm
5. Spindle model A2-6
6. Max. Spindle speed :max.4000r/min
Introduction
● Swing over lathe diameter 500mm
● Max. turning length 250mm
● Maximum rotation diameter of tool table Ø160
● Maximum bar material diameter 50mm
● Spindle model A2-6
● Max. Spindle speed :max.4000r/min
characteristic
Main Specification
Model of lathe | CK52-2 | |
Machining capacity | Max. swing diam. over lathe | Ø500mm |
Max. turning length | 250mm | |
Max.rotation diameter of tool table | Ø160mm | |
Maximum bar material diameter | Ø50 | |
Spindle | Spindle model | A2-6 |
Max. Spindle speed | max.4000r/min | |
Setting spindle speed | 1-3500 rpm | |
X/Z axis feeding | X-axis maximum travel | 1000 mm |
Z-axis maximum travel | 400mm | |
X/Z axis max. fast travel speed | 24m/min | |
Turret tools | Number of tools | 8 |
Static Tools dimension | 20x20 mm | |
Boring tools | Ø20 | |
Motor | Main motor power | SYNTEC 11kw |
Spindle motor torque | Rated 72 N.M | |
Other items | Slanting bed degree | 35 degrees |
Machine L x W x H | 1900 x1580 x 1700 mm | |
Machine net weight | 2600 kg | |
Total horse | 13 KW | |
average power consumption | 2kw/h |
Machine precision specification
Main inspection items | Detection method | factory standard |
Spindle radial run-out | Detect run-out of outer cone | 0.0025 |
X-axis repeat position | Detect repeated positioning of the X-axis. Note: First predict about 50 times to offset the error of the cold engine and hot engine, and then detect the repeated positioning. | 0.0025 |
Z-axis repeat position | Detect repeated positioning on the Z axis. Note: First predict about 50 times to offset the error of the cold engine and hot engine, and then detect the repeated positioning. | 0.0025 |
If the customer wants to test the ISO or VD1 accuracy of X/Z/Y axis, it shall be determined at the time of writing the contract. The customer must test this item at the same time of the initial acceptance of South Factory. |
Configuration standard accessories
Name | Specification | Brand |
NC controller | SYNTEC 22TA ,crystal panel10.4inches | Taiwan SYNTEC |
X/Z axis servo driver | Standard setting SYNTEC2.4KW (optional:YASKAWAI 1.3kw),X-axis motor with brake | China |
Spindle | Standard, Taiwan POSA | Taiwan POSA |
Spindle brake | Standard, Taiwan POSA | Taiwan POSA |
Closed loop indexing | The spindle is equipped with Taiwan's new generation original magnetic ring encoder | Taiwan |
Spindle motor | Standard,Beijing CBT | Beijing CBT |
Rotary cylinder | High speed rotary cylinder | Made in China |
X/Z-axis screw | C3 grade futures grinding screw with double nut.one end is blide threaded | Taiwan PMI or Hiwin |
X/Z-axis linear guild way | Roller P-level linear rail | Taiwan SYNTEC |
One piece casting base | The bed and base are all made of resin sand and cast in one piece, without adding cement. The internal stress removal method of the cast iron is completely vibrated/fully annealed/insulated/aging, and then placed for a period of time after finishing and then tested to pass the test. | Made in china |
Lubrication | Japan Valley brand lubricating oil pump (joint venture) | Made in China Foshan |
Hydraulic unit | Guangzhou ZhanPing hydraulic station | Made in China |
Cooling pump | Volume:1000 x 540 x 100,Water pump power 250w | Made in China |
Machine metal cover | The outer cover is made of national standard thick 2.0-0.03mm cold plate | Made in China |
Processing blow valve | Install 2 Air TAC solenoid valves to prepare for air blowing. The system controls the air blowing to realize the processing air blowing function. | Taiwan |
Electrical distribution box cooling | Use copper tubes (durable) to install environmentally friendly heat transfer media heat exchanges to cool down the circulation in the electrical box and keep it clean. | Made in China |
Electrical components | Schneider Electrical components | Made in China |
Oil mist separator | Separate part of the gas and liquid (or oil) in the mist | JFS |
power cable | 5 meters cable, high temperature resistance, wear resistance and corrosion resistance | Made in China |
Standard Accessories with machine
Item | Name | Specification | Quantity | Remark |
1 | Flexible collet | 1 pcs | ||
2 | Flexible chuck pull rod | 1PCS | ||
3 | Foot switch | 1PCS | ||
4 | Allen wrench | 1 set |
Technical data with the machine
item | name | specification | quantity | remark |
1 | Packing list | 1set | in accessories box | |
2 | Lathe control and program USB disk manual | 1 pcs | in accessories box | |
3 | Circuit digram | 1set | in accessories box | |
4 | Servo driver user manual | 1set | in accessories box |
Contact Us
+86 13928187729
+86 13928187729
manager@southlathe.com/ js_john@vip.163.com
No.3 Huafu Road, Bianjiaojuweihui, Ronggui town Shunde Foshan City, Guangdong Pronvice China.